Request Quote
Features
The crank-adjust single-point depth control is standard equipment on all models and offers the following benefits:
- More precise adjustment when changing the operating depth
- Easy access at the front of the machine
- Accurate, repeatable depth control
The three-bar disk gang model features a mechanical depth adjustment:
- Depth adjuster bolts (1) allow adjustment of individual gangs up or down within a 140-mm (5.5-in.) range.
An optional hydraulic depth adjustment (2) is available:
- Allows on-the-go hydraulic adjustments to be made from the tractor seat
- Gangs adjust up or down within a 140-mm (5.5-in.) range
The three-bar frame:
-
Is constructed of three ranks of standards
- Has strength to match higher horsepower tractors
- Handles heavier residue levels
Three-bar frame models have these strength features:
- One-piece welded construction
- Solid steel in rear mainframe member
- 102-mm x 102-mm (4-in. x 4-in.) cross members
- 51-mm x 102-mm (2-in. x 4-in.) side members
- 76-mm x 127-mm (3-in. x 5-in.) diagonal frame supports
The long narrow hitch design:
- Allows good maneuverability in tight headlands
- Is constructed of 51-mm x 127-mm (2-in. x 5-in.) steel tubing for strength
- Heavy cast-steel hitch link for yoke-type drawbars is standard equipment
- Hitch clevis is available for use with straight drawbars (not recommended for tractors over 150 engine hp)
A Level-lift™ linkage with easy turnbuckle leveling enables the mulch tiller to remain level whether in transport or in the field position.
A hitch jack is included with all models for storage and easier hookup to the tractor.
Coulter blades are for use where little incorporation is desired or for erosion-prone areas where it is important to disturb as little residue as possible. Blades are on 229-mm (9-in.) spacing to reduce the chance of plugging.
- Two-position blade down-pressure adjustment ensures consistent blade down pressure in light- or heavy-residue conditions.
- Coulter gangs have rigid scraper bars.
- Dura-Flex™ bearings and welded steel spools provide reliable performance and durability.
- Gangs are spring-cushioned with 140 mm (5.5 in.) of vertical travel to provide protection against rocks or other obstructions.
Rigid standard (figure 1):
-
In base equipment on all models
-
32 mm x 51 mm x 813 mm (1.25 in. x 2 in. x 32 in.)
-
Economical design is suited for fields having few obstructions
-
Till to a maximum depth of 279 mm (11 in.)
-
Good clearance to handle heavy trash
-
813 mm (32 in.) of underframe clearance
-
381-mm (15-in.) center-to-center spacing
-
Spring-reset 813-mm (32-in.) standard (figure 2):
- Optional on all models
- 32 mm x 51 mm x 813 mm (1.25 in. x 2 in. x 32 in.)
- Suited for fields having rocks or other obstructions
- Till to a maximum depth of 279 mm (11 in.)
- Trip height of 254 mm (10 in.) for good clearance
- 296-kg (650-lb) trip force
- Automatically resets to the original working position after clearing an obstruction
- Good clearance to handle heavy trash
- 813 mm (32 in.) of underframe clearance
- 381-mm (15-in.) center-to-center spacing
Tru-Depth standard (figure 3):
- Optional on all models
- 51 mm x 32 mm x 813 mm (2 in. x 1.25 in. x 32 in.)
- Edge bent for extra strength
- Designed to work in rocky ground and heavy draft conditions
- Till to a maximum depth of 279 mm (11 in.)
- Trip height of 279 mm (11 in.) for excellent clearance
- 568-kg (1250-lb) trip force
- Once an obstruction is cleared, the standard automatically returns to its original working position
- Excellent clearance to handle heavy trash
- 813 mm (32 in.) of underframe clearance
- 381-mm (15-in.) center-to-center spacing
A variety of shovels are available to match conditions:
- 76-mm x 610-mm (3-in. x 24-in.) concave twisted shovels for use in a wide range of average soil conditions are base equipment.
- 102-mm x 610-mm (4-in. x 24-in.) concave twisted shovels for use in light, sandy soils or where greater fracturing between the standards is desired, are optional equipment.
- 51-mm x 305-mm (2-in. x 12-in.) chrome carbide point chisel provides excellent strength and wear life in tough-to-penetrate conditions.
Typical percents of residue cover remaining are listed in the table. The percentages do not take into account variables such as the condition of the residue, speed and soil type.
Starting residue cover (percent) |
Remaining non-fragile* residue cover (percent) |
Remaining fragile** residue cover (percent) |
||||
|
with 2-in. x 14-in. shovel |
with 3-in. x 24-in. shovel |
with 4-in. x 24-in. shovel |
with 2-in. x 14-in. shovel |
with 3-in. x 24-in. shovel |
with 4-in. x 24-in. shovel |
100 |
65 |
55 |
50 |
45 |
40 |
35 |
90 |
55 |
50 |
45 |
40 |
35 |
30 |
80 |
50 |
45 |
40 |
35 |
30 |
28 |
70 |
45 |
38 |
35 |
30 |
28 |
25 |
60 |
40 |
33 |
30 |
27 |
25 |
20 |
50 |
32 |
27 |
25 |
22 |
20 |
17 |
40 |
25 |
22 |
20 |
18 |
15 |
14 |
*Non-fragile residue includes crops like corn, sorghum, wheat (more than 45 bu).
**Fragile residue includes crops like soybeans, edible beans, peas, wheat (under 45 bu), sunflower, peanuts, cotton.
Specs & Compare
Key Specs | Current Model |
Working width 2-bar | 1.9-3.43 m 6.25-11.25 ft |
Working width 3-bar | 3.43-6.48 m 11.25-21.25 ft |
Transport width | 2.1-4.4 m 7-14.33 ft |
Transport height | 1.35-3.4 m 4.42-11 ft |
Operating depth | Inches 27.9 cm 11 in. |
Miles per hour | 8-11 km/h 5-7 mph |
Horsepower per shank | 8.95-14.9 kW 12-20 hp |
Standard spacings | Inches 38.1 cm 15 in. |
Fold | |
Type | Rigid: 3-section |
Working width | |
Option 1 | 2-bar: 1.9 m 6.25 ft |
Option 2 | 2-bar: 2.67 m 8.75 ft |
Option 3 | 2-bar: 3.43 m 11.25 ft |
Option 4 | 3-bar: 3.43 m 11.25 ft |
Option 5 | 3-bar: 4.2 m 13.75 ft |
Option 6 | 3-bar: 4.95 m 16.25 ft |
Option 7 | 3-bar: 5.72 m 18.75 ft |
Option 8 | 3-bar: 6.48 m 21.25 ft |
Option 9 | |
Option 10 | |
Transport width | |
Option 1 | 2.1 m 7 ft |
Option 2 | 2.67 m 8.75 ft |
Option 3 | 3.7 m 12 ft |
Option 4 | 3.7 m 12 ft |
Option 5 | 4.3 m 14 ft |
Option 6 | 5 m 16.5 ft |
Option 7 | 4.4 m 14.33 ft |
Option 8 | 4.4 m 14.33 ft |
Option 9 | |
Option 10 | |
Transport height | |
Option 1 | 1.35 m 4.42 ft |
Option 2 | 1.35 m 4.42 ft |
Option 3 | 1.35 m 4.42 ft |
Option 4 | 1.3 m 4.33 ft |
Option 5 | 1.3 m 4.33 ft |
Option 6 | 1.3 m 4.33 ft |
Option 7 | 3.2 m 10.33 ft |
Option 8 | 3.4 m 11 ft |
Option 9 | |
Option 10 | |
Number of shanks - fold | |
Option 1 | Rigid: 5-shank |
Option 2 | Rigid: 7-shank |
Option 3 | Rigid: 9-shank |
Option 4 | Rigid: 9-shank |
Option 5 | Rigid: 11-shank |
Option 6 | Rigid: 13-shank |
Option 7 | Folding: 15-shank |
Option 8 | Folding: 17-shank |
Option 9 | |
Option 10 | |
Operating depth | |
Inches | 27.9 cm 11 in. |
Operating speed | |
Miles per hour | 8-11 km/h 5-7 mph |
Horsepower required | |
Horsepower per shank | 8.95-14.9 kW 12-20 hp |
Depth control | |
Options | Single point on 3-bar machines |
Hitch | |
Type | Turnbuckle leveling adjustment: Tube: 51x127 mm 2x5 in. |
Frame | |
Description | Rigid frame: cross members: 102x102 mm 4x4 in. Side members: 51x102 mm 2x4 in. Diagonal frame supports: 76x127 mm 3x5 in. |
Underframe clearance | 81.3 cm 32 in. |
Standard spacings | |
Inches | 38.1 cm 15 in. |
Standard options | |
Option 1 | Spec 32x51x813 mm 1.25x2x32 in. Rigid |
Option 2 | Spec 32x51x813 mm 1.25x2x32 in. Trip clearance: 254 mm 10 in. Trip force: 295 kg 650 lb Trip force 295 kg 650 lb Trip height 25.4 cm 10 in. Spring-reset |
Option 3 | Spec Edge bend: 51x32x813 mm 2x1.25x32 in. Trip clearance: 279 mm 11 in. Trip force: 567 kg 1,250 lb Trip force 567 kg 1,250 lb Trip height 27.9 cm 11 in. Tru-Depth |
Disk coulters/gangs | |
Description | One set at front of machine |
Type | Disk or coulter |
Blade size | 50.8x0.65 cm 20x0.256 in. On 2-bar: 0.45 cm 0.177 in. |
Coulter size | 50.8x0.5 cm 20x0.197 in. |
Blade/coulter spacing | 22.9 cm 9 in. |
Type of scrapers | Rigid bar |
Type of protection | Coil spring |
Gang shaft | 7.62x10.2 cm 3x4 in. |
Wheels and tires | |
Option 1 | Single wheel - 9.5L-15FI Load Range D (2-bar design) |
Option 2 | Single wheel 11L-15FI Load Range D (3-bar) |
Option 3 | Walking tandem - 9.5L-15FI Load Range D (3-bar) |
Option 4 | Walking tandem - 11L-15FI Load Range D (3-bar) |
Additional features | |
Option 1 | |
Option 2 | |
Option 3 | |
Additioanl information | |
Date collected | |
Ground-engaging components | |
Options |